tig mig portable fume extractor belongs to the mechanical shake dust collector, its basic structure is composed of three parts: fan, filter and dust collector, each part is installed in a vertical frame, steel plate shell, baking paint anti-rust, easy to operate and use. Fan adopts centrifugal fan, large air volume, high wind pressure, and adopts noise reduction measures, low noise. The filter adopts flat cloth bag group, each cloth bag is equipped with spring steel wire mesh, the filtering effect is good. The flyaway mechanism uses the motor to drive the eccentric wheel and the connecting rod to make the cloth bag shake and stick to the dust on the surface of the filter bag. The dust collector is equipped with an access door for easy maintenance and bag changing.

tig mig portable fume extractor What are the contents that need regular inspection? Here, for you to talk about in detail:

First, tig mig portable fume extractor regularly inspect the operation of the ash cleaning device, if it is found that the electromagnetic pulse valve is abnormal, the switch valve is not in place or air leakage, the vibration mechanism is faulty, etc., should be dealt with in time.

Second, for rotary tig mig portable fume extractor, regularly referred to as the operation of the rotary mechanism, not less than twice a day.

Third, regularly check the pressure of the gas bag, when the pressure is higher than the upper limit or lower than the line, the fault should be immediately discharged.

Fourth, regularly check the working state of the air compressor, including the oil level, exhaust pressure and pressure rise time, etc., no less than three times a day, regularly release the water of the buffer tank and the gas storage tank no less than once a day, and regularly inspect the compressed air device no less than once a day.

6, tig mig portable fume extractor ash hopper when unloading ash, should be synchronized to check the operation of the ash valve and ash conveying device, found abnormal timely treatment.

7. Often pay attention to the dust emission concentration of tig mig portable fume extractor inlet and outlet, regularly check the dust filter bag, observe the damage condition, and find that the dust filter bag is damaged, the filter bag should be replaced in time.

tig mig portable fume extractor cleaning mechanism is the use of electric motor to drive the pain wheel, the connecting rod to make the cloth bag vibrate and remove the dust on the surface of the filter bag. Its control installation is divided into two kinds: automatic control and manual control. Automatic control means that when the fan continues the task, the single-bag dust collector flying mechanism actively vibrates ash on time, the manual fan dust collector stops the active task of the flying mechanism, actively stops after tens of seconds, and can also start the dust cleaning motor at any time according to the demand, the length of cleaning time is adjusted by the user. Structure performance characteristics: tig mig portable fume extractor, dust collector is a small volume, dust removal of air purification equipment. Suitable for a variety of vertical dust production points, flexible and convenient, local dust collection, local treatment, can be clean air. The basic structure is composed of dust removal box, centrifugal fan, filter bag (filter cartridge), dust collector and microcomputer controller, etc. The dust is sucked inside the dust collector box by the negative pressure of the fan through the dust suction pipe, and the coarse particle dust is initially filtered by the filter and directly dropped to the dust collector by the filter, and the fine dust is captured by the filter on the outer surface. Clean gas is filtered, decomposed and purified by the filter element into the clean room, and then discharged from the outlet by the fan.

The dust-containing gas enters the dust collector from the lower part of the dust collector and is filtered through the dust bag, and the clean air is discharged by the induced draft fan. After the dust collector works for a period of time, the dust on the filter bag gradually increases, causing the Yin force of the filter bag to rise, and the dust collector needs to be cleaned, and the dust collector will work normally after the cleaning is completed. tig mig portable fume extractor unit has six specifications, divided into three, a kind of door, a kind of drawer, a kind of neither a door nor a drawer; The lower part of the addition is directly connected to the dust removal equipment such as the top of the warehouse, the bunker, the transportation point of the belt transportation, etc., the dust direct recovery Dust collector Usage Description tig mig portable fume extractor, installed in the vicinity of the mechanical equipment that produces dust, and is provided by the user according to the size of the upper inlet of the dust collector. Configure the metal or plastic pipe and dust cover (can also be designed by the manufacturer), the dust collector should check the access door before the work, the flange connection is sealed, so as to avoid air leakage, reduce the dust removal effect. Dust collector, voltage, from the dust collector external wire street power supply can start to use, the initial operation, should pay attention to the fan rotation direction (such as reverse, need to replace the power wiring. The cover of the dust collector control cabinet can not be opened at will in the studio, if it is necessary to adjust the cleaning time, or repair the circuit, it should be stopped or cut off the power supply. According to the nature of dust and the size of dust concentration, adjust the timing of cleaning. Vacuum cover is a key part of the dust collector in the state, the use of units should be connected according to the size of the workpiece and the nature of the dust, close, seal, and design the principle of dust cover, the production of ideal dust cover.

tig mig portable fume extractor https://www.kaisenfilter.com/Mobile-welding-fume-extractor-for-TIG-MIG.html